Wyze cam flashing yellow and blue

Jul 3, 2020 · Power off your camera and insert your microSD card. Hold the setup button, plug in your USB cable, keep holding the setup button for 3-6 seconds until the light is solid blue, then release the button. Note: The “Solid Blue” in this case is not the same as the one normally seen on the camera.

This is the second Wyze Cam Pan for me to do this same thing. I noticed that the lights were flashing yellow/blue and the device was restarting every 30 seconds by seeing it spinning and doing the set up process. I’ve power cycled it about a hundred times and even removed it from my device list on my app. When I attempt to add it back to my …The SD format tool formatted mine FAT32 and it worked first shot. This worked for me as well. Download app and format card. Blue solid light! I tried using the app on a 64gb SDXC Card. The process didn't work and it was formatting as exFAT. On my Mac I was able to format the volume to "MS-DOS (FAT32)" and once I copied the firmware back on was ...Once complete, the status light will flash yellow and blue at the same time (not alternating). Wyze Cam will continue to flash yellow and blue at the same time if the webcam firmware is installed properly and the camera is turned on. To use your new webcam: Connect the USB A to A cable to the Wyze Cam USB port and the computer USB port.August 10, 2022 15:55 Presents as: After completing a firmware update the camera is no longer responsive. Troubleshooting: Try power cycling the camera by unplugging it for about 30 seconds and then plugging it back in. If you have an extra power cable and/or adapter, switch those out to see if that alleviates the issue.iOS: Camera+ is our favorite photography app for iPhone, and today it gets a few cool updates as well as $1 off the regular price. iOS: Camera+ is our favorite photography app for iPhone, and today it gets a few cool updates as well as $1 o...

V2 flashing blue/yellow I have a V2 camera that was unplugged a few months ago to plug Christmas lights in, in the mean time we changed internet providers. I just plugged the camera back in and tried to "add device" but the camera will only blink blue/yellow.Nov 6, 2020 · Solid blue light: Camera is successfully powered and connected to the network. Flashing yellow and blue light: Camera is pairing with the Base Station. Flashing red light: Camera is plugged into power and charging. Flashing red light, quickly: Camera restart needed. Press and hold SYNC button for 10 sec to restart cam. Flashing yellow and blue for the LED Status means it's trying to connect to the network. Try these steps: Power cycle the camera by unplugging the power and plugging it back in. If the camera returns to flashing yellow but never reconnects, set the camera up as a new device. On the Home tab of the Wyze app, tap the + plus sign in the upper left ...To set up your Wyze Base Station: Connect your mobile device to the same Wi-Fi network your base station will be set up to. In the Wyze app, tap Home, then tap + plus sign on the top left. Tap Add Device. Tap Cameras > Wyze Base Station > Next. Plug one end of the included power supply cable into the base station, and the other end into a power ...Fixing Wyze Base Station Flashing Blue. Change Ethernet Cable. If your base station is in perfect shape, then the first thing you should do is change the ethernet cable. Several owners have pointed out that the issue with the base station flashing is mostly related to a defective ethernet cable.It went from solid yellow light to flashing yellow & blue. It stayed flashing yellow & blue light after it is powered and doesn’t change or do anything. The other one is just solid yellow and does nothing too. ... Wyze Cam v2 and Pan firmware files can be found on the Release Notes page. Download a specific version of firmware, For Windows …StopICU33: Tried that on a new cam at first connection, when the app suggested it.(I had done the update to the first cam at first connect, and it updated just fine.) On the second cam, the update failed. When powered up now, the cam displays a continuous yellow status lite for 30-45 seconds, you hear the IR filter switch in the …Next I decided to delete the camera from my app in hopes of resetting everything again, but now the camera is stuck in an endless loop of flashing the blue and yellow light, panning around the area, and then turning off. It turns back on again after several minutes on its own and it does the same flashing lights and pan again and turns …

Doing so should help delete all the stored settings inside the camera. In order to factory reset, simply hold the setup button for 20-30 seconds. Reflash the Firmware in the Camera. A few users have managed to fix the solid yellow light by flashing firmware in the camera. Flashing firmware inside the camera will require you to have access to a ...Wait 3-4 minutes. The camera will reboot, and the light status will change during this time. Once complete, the status light will flash yellow and blue at the same time (not alternating). Note: Wyze Cam will continue to flash yellow and blue at the same time if the webcam firmware is installed properly and the camera is turned on.Hello was wondering if anyone had an issue with indoor wired camera. I plug it in and it immediately starts blinking yellow slowly not fast. I have.Step 5: Complete the setup on your Wyze app. Open the application on your smartphone. Press the Add Device (+) button on the upper left side of your screen. Under Power & Lighting, tap Wyze Plug. Choose Next. Wait for your Wyze plug to finish connecting with the app via Bluetooth.Oct 5, 2022 · Doing so should help delete all the stored settings inside the camera. In order to factory reset, simply hold the setup button for 20-30 seconds. Reflash the Firmware in the Camera. A few users have managed to fix the solid yellow light by flashing firmware in the camera. Flashing firmware inside the camera will require you to have access to a ...

The walten files plush.

The status light is a solid yellow now. I’d still really like to get this back on a stock Wyze firmware but at least I don’t have a complete brick now. Edit 1: Yellow light turned off. Seems to come and go, perhaps based on writes to storage activity. Edit 2: Tried reflashing to Wyze. Back to useless blinking yellow/blue again.After about 10 seconds, the light will change from yellow to solid yellow and blue at the same time (it may appear as just solid blue). Both LEDs are lit here showing that it is in the process of flashing the firmware. If your camera is not changing from yellow, make sure you are using an sd card with less than 32GB of storage (not sdxc).Pan/Tilt/Zoom. Use the control panel in the Wyze app to pan and tilt the camera for a 360° live view. Pan Scan™. Automatically scans its surroundings by rotating to up to 4 custom waypoints. CMOS Starlight sensor. Reduces noise from low light, sees in environments up to 25x darker. Versatile mounting. Magnetic, screw, and 1/4-20 tripod …The LED is flashing that way because it’s trying to connect to the original network, not your phone. Unless of course you setup the camera on a WiFi hotspot on your phone. My understanding as far as leaving it disconnected from the WiFi is it will still record to the SD card.

Oct 31, 2022 · Plug Wyze Base Station into a different power outlet. If this helps, then the power outlet may not be powered. Try using a different Ethernet cable. If this helps, then the cable itself may be faulty. Try a soft reset. Hold down the Sync button on the base station until the status light turns solid yellow. Once the status light begins flashing ... Apr 13, 2023 · Tap the settings icon > Wyze Support > Submit a log. Choose Doorbell > Connectivity Issues. Press in on the doorbell while also pushing it up to remove it from the backplate. This exposes the back wiring and setup button. Press and hold the setup button until the status light turns solid yellow. Once the light turns solid yellow, release the ... Next I decided to delete the camera from my app in hopes of resetting everything again, but now the camera is stuck in an endless loop of flashing the blue and yellow light, panning around the area, and then turning off. It turns back on again after several minutes on its own and it does the same flashing lights and pan again and turns off again.May 20, 2020 · Wyze Cam will continue to flash yellow and blue at the same time if the webcam firmware is installed properly and the camera is turned on. When I reread. Want to revert the webcam firmware update? I must have missed importance of: Visit the Release Notes page for the latest Wyze Cam v2 firmware file. Check the status light on the Base Station and Wyze Cam Outdoor v1/v2. They should both be solid blue. If either are flashing, then they're trying to connect or pair. Check the signal strength between the camera and the Base Station it's attached to. In the Wyze app, tap on the paired Wyze Base Station. A full signal is three total bars: . If ...Welcome to the Forum @var.bolivar69! Here is some information regarding your light status from the LED Status Light Indicator Knowledge Article. Flashing yellow, yellow and blue, or blue Note: The same troubleshooting steps will be taken if the status light is flashing. Power cycle the camera by unplugging the power and plugging it back in. If the camera returns to flashing yellow but never ...Wait 3-4 minutes. The camera will reboot, and the light status will change during this time. Once complete, the status light will flash yellow and blue at the same time (not alternating). Note: Wyze Cam will continue to flash yellow and blue at the same time if the webcam firmware is installed properly and the camera is turned on.I would recommend against mounting this one in the hard to reach location for now. If you have another that doesn't have the flashing light you should probably use that for now. TheVulkanMan is correct about what the flashing blue light means during setup. However, after setup that means that your Wyze Cam has lost connection to the router.

Wyze Cam Outdoor. Solid yellow light: Camera is starting up, powering on. Flashing yellow light: Travel mode is enabled. Flashing blue light: Camera is connecting to the Base Station's network. Solid blue light: Camera is successfully powered and connected to the network.

Sep 13, 2020 · Hello, I had 2 wyze cam v2 that has been sitting in box for over an year. I already have one installed and working well. I tried installing the 2 new ones today. Both of them got installed and went through firmware upgrade & hung up. I had to download the firmware in SD card and flash it as recommended in forums. When I did this it it went from yellow to blue light and after few minutes the ... Flashing your WyzeCam v2 firmware. Beta. WyzeTao March 23, 2018, 7:25pm 1. Here is the instruction: (different from v1 firmware) Download a specific version of firmware, unzip it, put it on root directory of your SD card and rename it to ‘demo.bin’ (Starting from 4.9.2.18, you don’t need the ‘rename’ step. We change the name to demo ...Nov 27, 2021 · The status light on your Wyze camera blinks a number of different colors depending on the status of the system. A flashing blue light means that your Wyze camera is connected to the Internet at your home. However, it also means that the Wyze camera is finishing its setup process and should be ready for use soon. I had an issue before with getting a camera to reset, and spoke with a tech via chat. They instructed me to download some firmware and to manually flash the firmware. That solved the issue with that camera, but it will not work for this camera. When I plug it in, it starts off solid yellow, then goes to flashing blue. All I want to do is factory reset it so I …Solid yellow light: The device is powered. Flashing yellow light: Waiting for connection. Flashing yellow/blue light: Connecting to router. Flashing blue light: Connecting to external network. Solid blue light: Connected. Flashing blue/purple light: Doorbell has been pressed. Solid purple light: 2-Way Audio is active.Power cycled camera through Wyze app. Cam is stuck at blue blinking light unable to connect. Steps taken to resolve: Tried 4 different power outlets (Directly to Known good power outlet & tried with 2 known good power strips) Get through setup but camera fails to finish and says to rescan QR code.Wyze Cam v3- can't get past blinking red light. Cameras. cam-v3. silvie February 15, 2022, 2:51am 1. I bought the Wyze v3, downloaded the app, got the camera started and everything seemed to be working fine. Then I moved the camera around, and noticed it was no longer working- the scene it was monitoring was frozen at a certain …Wyze Cam will continue to flash yellow and blue at the same time if the webcam firmware is installed properly and the camera is turned on. When I reread. Want to revert the webcam firmware update? I must have missed importance of: Visit the Release Notes page for the latest Wyze Cam v2 firmware file.

Good day ascension home page.

Weathering gizmo answers key activity b.

The status light is a solid yellow now. I’d still really like to get this back on a stock Wyze firmware but at least I don’t have a complete brick now. Edit 1: Yellow light turned off. Seems to come and go, perhaps based on writes to storage activity. Edit 2: Tried reflashing to Wyze. Back to useless blinking yellow/blue again.HowStuffWorks takes a look at primary colors, why understanding them is important and how they are so much more than red, yellow and blue. Advertisement Go ahead and ask Google — the knower of all things — to name the primary colors. You'll...Understanding your Wyze Cam OG Status Light Brenda April 07, 2023 00:19. All Wyze devices have a handy status light that helps determine what state the device is in. ... Flashing blue light - The camera is connected and finishing setup. Solid blue light - Camera is powered, connected, and working properly.V2 flashing blue/yellow I have a V2 camera that was unplugged a few months ago to plug Christmas lights in, in the mean time we changed internet providers. I just plugged the …Once complete, the status light will flash yellow and blue at the same time (not alternating). Wyze Cam will continue to flash yellow and blue at the same time if the webcam firmware is installed properly and the camera is turned on. To use your new webcam: Connect the USB A to A cable to the Wyze Cam USB port and the computer …Wyze Cam will continue to flash yellow and blue at the same time if the webcam firmware is installed properly and the camera is turned on. When I reread. Want to revert the webcam firmware update? I must have missed importance of: Visit the Release Notes page for the latest Wyze Cam v2 firmware file.Unplug camera, place sd card in cam, press and hold the setup button (I’ve found that placing the camera upside down on a table and pushing into the table helps the akwardness), keep holding the setup button and plug in the cam. When you see the led light in back shine yellow and blue at once then let go of the setup button.Ever since getting a Synology diskstation I’ve been trying to flash both my Wyze V2 cams without much luck. II first downloaded the firmware. Put the card in the camera. Held down the, “Miniscule,” button until the light turned solid blue. Went to the software>setting>advanced and no mention of RTSP. A few Questions. Under Settings. Device info> Firmware Should it list the RTSP version ...Tap the settings icon > Wyze Support > Submit a log. Choose Doorbell > Connectivity Issues. Press in on the doorbell while also pushing it up to remove it from the backplate. This exposes the back wiring and setup button. Press and hold the setup button until the status light turns solid yellow. Once the light turns solid yellow, release the ...Pressing Setup button for 1,3,10,20,30 seconds didn’t help. Rebooting camera, phone and router didn’t help. I eventually tried a firmware update (using .193 as that’s in my other cameras) on 32GB Micro SD card. Afterwards light was flashing blue and I was able to press the Setup button and do a clean install. ….

Check the floodlight’s detection settings. In the Wyze app, go to your floodlight’s settings. Under Floodlight Control, tap Auto. Under Turn on when dark, select Motion is detected by camera. Power cycle the floodlight and camera. Start by flipping the breaker to the off position. Wait 5-10 seconds, and then turn the breaker back to the on ...Flashing your WyzeCam v2 firmware. Beta. WyzeTao March 23, 2018, 7:25pm 1. Here is the instruction: (different from v1 firmware) Download a specific version of firmware, unzip it, put it on root directory of your SD card and rename it to ‘demo.bin’ (Starting from 4.9.2.18, you don’t need the ‘rename’ step. We change the name to demo ...If the setup process is stuck at the “Finishing Setup” screen and the status light is solid blue: Press the X icon in the upper right-hand corner to exit the setup process. Go to the Home tab of the Wyze app and drag down the device list to refresh it. Your Wyze Battery Cam Pro should have been successfully added. If not, proceed to the ...May 8, 2023 · Understanding your Wyze Cam v3 Status Light ... Flashing blue light: Camera is connected, still finishing setup Firmware update (quick flashing blue light) The blue bumper sticker with two yellow stripes is the logo of the Human Rights Campaign, or HRC. It stands for equality in the lesbian, gay, transgender and bisexual community. Today, the logo is seen on bumper stickers, Facebook walls, t-...Oct 4, 2021 · Scroll down to the WyzeCam V2 section and click the blue version number for a firmware file to flash. Once downloaded, rename the file to demo.bin and then copy it to the root of the SD card. Remove the SD card and unplug the camera. Hold the “Setup” button on the back and then plug the camera back in while continuing to hold the setup button. Welcome to the Forum @var.bolivar69! Here is some information regarding your light status from the LED Status Light Indicator Knowledge Article. Flashing yellow, yellow and blue, or blue Note: The same troubleshooting steps will be taken if the status light is flashing. Power cycle the camera by unplugging the power and plugging it back in. If the camera returns to flashing yellow but never ...The LED is flashing that way because it’s trying to connect to the original network, not your phone. Unless of course you setup the camera on a WiFi hotspot on your phone. My understanding as far as leaving it disconnected from the WiFi is it will still record to the SD card.Flashing your WyzeCam v2 firmware. Beta. WyzeTao March 23, 2018, 7:25pm 1. Here is the instruction: (different from v1 firmware) Download a specific version of firmware, unzip it, put it on root directory of your SD card and rename it to ‘demo.bin’ (Starting from 4.9.2.18, you don’t need the ‘rename’ step. We change the name to demo ...May 21, 2020 · Greetings tomp, Thanks for your response. During the step where you hold down the setup button while plugging in USB cable and continue to hold button, I get a momentary yellow light and then light changes to blinking light (pale) blue (blue and yellow together) and it goes on forever. The above was my reply to you until I looked at instructions again and discovered I wasn’t having to rename ... Wyze cam flashing yellow and blue, The status light is a solid yellow now. I’d still really like to get this back on a stock Wyze firmware but at least I don’t have a complete brick now. Edit 1: Yellow light turned off. Seems to come and go, perhaps based on writes to storage activity. Edit 2: Tried reflashing to Wyze. Back to useless blinking yellow/blue again., Just got the camera today…. I set it up at home in a WiFi environment, set it up to detect motion, added my MicroSD card, tested it, all was good. Then took it down to our condo …, May 8, 2023 · Understanding your Wyze Cam v3 Status Light ... Flashing blue light: Camera is connected, still finishing setup Firmware update (quick flashing blue light) , To set up your Wyze Base Station: Connect your mobile device to the same Wi-Fi network your base station will be set up to. In the Wyze app, tap Home, then tap + plus sign on the top left.; Tap Add Device.; Tap Cameras > Wyze Base Station > Next.; Plug one end of the included power supply cable into the base station, and the other end into …, The last link that was sent to me was for installing firmware for use of the Wyze Cam v2 as a web cam. I do not want to use it as a web cam. I also made sure to use the power adapter that came with it, 5V, 1A power adapter. The light turns on yellow and starts blinking slowly while the camera clicks. To clarify, this is a Wyze Cam v2, Model WYZEC2., , Less than 2 week old Samsung endurance pro 64gb card. It bricked when I followed the 'manually flash firmware' article. It says to remove sdcard and power off, hold setup and insert power cable, continue holding setup for "3-6 seconds or until light turns blue (not the regular blue but a yellow-blue/light blue)"., For beach-goers, experts always recommend a healthy coating of sunscreen to protect the skin from those pesky ultraviolet (UV) rays. But sunlight contains more than just UV light. In fact, it’s made up of red, green, yellow, blue and orange..., I know this is an old topic and I hate to revive old threads but I have a Wyze cam V2 that I set up on Wi-Fi. I disconnected it to take to work to record something. It won’t connect to the Wi-Fi at work because it’s an open network and it’s only 5Ghz not 2.4. But I read somewhere that it would still record off-line and you should have either a blue or …, This will reset the camera. For Wyze Cam v1 only: Press and hold it for 20 seconds. Wait at least 30 seconds for the unit to initiate. This process can take up to 5 minutes. It's rare, but it's possible. The LED status light on the device will change from Solid Yellow to Blinking Yellow. For Wyze Cam v3 only: The light will turn red., If you have a second Wyze Cam, test the Bridge with a second camera to see if the problem persists. If the Status Light is flashing blue & yellow or flashing blue: Make sure the camera that the Bridge is paired to has the latest firmware version installed. Open the Wyze app, go to the Account tab found on the bottom right. Then tap Firmware ..., Plug in your USB cable while pressing and holding the setup button. Continue to hold down the setup button until the status light flashes solid blue (the led flashes blue and yellow at the same time, giving off a blue hue). Wait for a couple of minutes. After the camera has finished booting, the status light will change. Wyze Cam v1, Welcome to the Forum @var.bolivar69! Here is some information regarding your light status from the LED Status Light Indicator Knowledge Article. Flashing yellow, yellow and blue, or blue Note: The same troubleshooting steps will be taken if the status light is flashing. Power cycle the camera by unplugging the power and plugging it back in. If the camera returns to flashing yellow but never ..., August 10, 2022 15:55 Presents as: After completing a firmware update the camera is no longer responsive. Troubleshooting: Try power cycling the camera by unplugging it for about 30 seconds and then plugging it back in. If you have an extra power cable and/or adapter, switch those out to see if that alleviates the issue., Flash Firmware for Wyze Cam v2 & Wyze Cam Pan Wyze Cam v2 and Pan firmware files can be found on the Release Notes page. Download a specific version of firmware, For Windows 10: Right-click on the folder and select extract all. For Mac: Just drag and drop the folder, put it on the root directory of your microSD card. For both Mac and …, The status light is a solid yellow now. I’d still really like to get this back on a stock Wyze firmware but at least I don’t have a complete brick now. Edit 1: Yellow light turned off. Seems to come and go, perhaps based on writes to storage activity. Edit 2: Tried reflashing to Wyze. Back to useless blinking yellow/blue again., Solid blue light: Camera is successfully powered and connected to the network. Flashing yellow and blue light: Camera is pairing with the Base Station. Flashing red light: Camera is plugged into power and charging. Flashing red light, quickly: Camera restart needed. Press and hold SYNC button for 10 sec to restart cam., I want cam to function as before. Regards, Grandpa Dave (dadrett) Omgitstony Forum Maven May 20 dadrett41: The light blue light is the blue and orange together. The instructions caution not to confuse with this with My Wyze webcams are blinking like this and are working as webcams, the light blue (blue and yellow led blinkin..., Wyze Cam will continue to flash yellow and blue at the same time if the webcam firmware is installed properly and the camera is turned on. When I reread. Want to revert the webcam firmware update? I must have missed importance of: Visit the Release Notes page for the latest Wyze Cam v2 firmware file., It went from solid yellow light to flashing yellow & blue. It stayed flashing yellow & blue light after it is powered and doesn’t change or do anything. The other one is just solid yellow and does nothing too. ... Wyze Cam v2 and Pan firmware files can be found on the Release Notes page. Download a specific version of firmware, For Windows …, Understanding your Wyze Cam Pan v3 Status Light Brenda March 16, 2023 20:28. All Wyze devices have a handy status light that helps determine what state the device is in. ... Flashing blue light - The camera is connected and finishing setup. Solid blue light - Camera is powered, connected, and working properly., Apr 6, 2023 · Flashing red light - Ready to connect to Wi-Fi. Flashing red and blue lights - Connection is in progress. Flashing blue light - The camera is connected and finishing setup. Solid blue light - Camera is powered, connected, and working properly. After Setup is Complete. Solid red light - Live stream is being viewed or a recording is in progress. , Mar 10, 2021 · If you have a second Wyze Cam, test the Bridge with a second camera to see if the problem persists. If the Status Light is flashing blue & yellow or flashing blue: Make sure the camera that the Bridge is paired to has the latest firmware version installed. Open the Wyze app, go to the Account tab found on the bottom right. Then tap Firmware ... , Once complete, the status light will flash yellow and blue at the same time (not alternating). Wyze Cam will continue to flash yellow and blue at the same time if the webcam firmware is installed properly and the camera is turned on. To use your new webcam: Connect the USB A to A cable to the Wyze Cam USB port and the computer …, The camera’s status light will turn solid yellow when powered. When flashing, it’s ready for setup. To set up your Wyze Cam or Wyze Cam Pan: In the Wyze app, tap Home, then tap the + plus sign on the top left. Tap Add Device. Tap Cameras > Wyze Cam or Wyze Cam Pan. With your camera plugged into an outlet, tap Next in the app., If the setup process is stuck at the “Finishing Setup” screen and the status light is solid blue: Press the X icon in the upper right-hand corner to exit the setup process. Go to the Home tab of the Wyze app and drag down the device list to refresh it. Your Wyze Battery Cam Pro should have been successfully added. If not, proceed to the ..., Flashing yellow, yellow and blue, or blue Note: The same troubleshooting steps will be taken if the status light is flashing. Power cycle the camera by unplugging the power and plugging it back in. If the camera returns to flashing yellow but never reconnects, set the camera up as a new device. On the Home tab of the Wyze app, tap …, The status light on your Wyze camera blinks a number of different colors depending on the status of the system. A flashing blue light means that your Wyze camera is connected to the Internet at your home. However, it also means that the Wyze camera is finishing its setup process and should be ready for use soon., Less than 2 week old Samsung endurance pro 64gb card. It bricked when I followed the 'manually flash firmware' article. It says to remove sdcard and power off, hold setup and insert power cable, continue holding setup for "3-6 seconds or until light turns blue (not the regular blue but a yellow-blue/light blue)"., Note: The “Solid Blue” in this case is not the same as the one normally seen on the camera. Instead, both the blue and yellow LEDs will be on at once, making it appear to be a lighter blue.* This is what I was referring to as the blinking light blue light. Problem is it continues to blink - never turns blinking yellow or solid “dark” blue., If nothing works, I would just roll back to the previous firmware for the Wyze Cam V2. Manual Firmware Update. Look under “Flash Firmware for Wyze Cam v2 & Wyze Cam Pan”. Remember to rename the file to demo.bin. FrauSchlau November 7, 2022, 3:30am 48. Thank you for the suggestion @JoeWyze., Wyze Cam v2 keep blinking Yellow Blue. I have disconnected and reconnected the power cord few times but still blinking yellow and blue , not getting solid yellow, any suggestions? 3. , Insert your microSD card into the Base Station and power cycle the Base Station to begin the firmware flash process. The status light will either stay solid yellow or immediately start flashing blue. Once the flash is complete, the Base Station will reboot itself. Wait until the status light becomes solid blue again.